rev62：
1. fix LED status of IN22


rev61：
1. Avoid instance out of range

rev60
1. add bigger delay after write E2 to match different E2PROM chip


rev56:
1. 兼容GD芯片
2. add check_TXEN()

rev53:
1. 修改写wifi静态IP，之前命令放在连接路由的后面不能成功执行
2. 避免wifi mac地址在出货时写成0x10 0x10...
3. 修改T3 label的名字，AO是T3000的关键字不能用改为T3-AO

rev52:
1. update baclib, update AI& BI automactically
2. clear deadmaster if any communication
3. fix default label
4. fix inital wifi mac address

rev51
1. compitable with new hardware with WIFI

rev50
1. fix stroing bacnet instance

rev47 （8o & 22i）
1. add TYPE3
2. fix interval of storing data to flash memory (旧版本会等待很长时间才存入flash)

REV46 for T3-8O
1. fix write output relinquish
2. Add dead master
3. add tcpip_initial if ethernet error

rev44
1.Fixed a problem where Bacnet Instance could not be stored properly

rev43
1. change MAX_TBLS to 5

rev42
1.for t3-22i, fix intpu issuse when range is 10K

rev41
1. fix input problem (input is wrong in rev39,rev40)

rev40
1. update bacnet library,support Writing instance and max_master
2. add MAX_MASTER
3. suspend MSTP polling to keep bus silent,it is private thing for temco
4. add new EEPROM_BAUDRATE to avoid to be changed in older bootlader(rev54)

rev39:
1. add pt1k sensor( intput is wrong in rev39, rev40, fixed it in rev41)
2. fix netmask issue

rev38:
1. speed up inputs scan interval, add delay when range is high speed count
2. fix led when input is digital.

rev36:
1.fix IN4 issue when range is high speed, slow down scanning input
2.fix uip_hostaddr_submask

rev33
1. update bacnet lib, support panel up to 254

rev32
1. support ptransfer_to_modbus
2. for pulse counter, support 10HZ, last rev only support 1 Hz
3. change jumper to 0-10v when range is pulse counter
4. fixed LED issue, AI12 TO AI22, range is thermsitor, led status is wrong


rev31
1. fix watchdog for all products
2. add output relinguish

rev29
1. when there are ip conflict in subnet, T3000 will send out command to change conflict ip

rev28
1. for a udp connection, do not response broadcast packet unless they are not in same subnet.


rev27:
1. use bacnet_Rev12.lib, add feature which support change vendor id.
rev26: 
1. (only for T3-22i)fix IN4 high speed count issue, caused by speeding up reading inputs. 
2. (only for T3-22i)fix led status when inputs are high speed count.
REV25：fix bacnet object number, only for t3-pt112  
REV24: speed up reading inputs
REV23：add new bacnetlib
REV22: fix custom tables and input type

REV19：add a av the make the module switch the bacnet to modbus.  fix the bug when you  change baud to 115200 ,it back to 57600 .
REV18: change the bacnet number from basing 0 to  basing 1 .
REV17: make the bacnet  mac address ,  port  can be changed . 
REV16: change the sendbuf length。
rev15  set the range , we will set the digit and analog auto .
rev14: fix pulse count for T3-22AI. AND FIX  the comunication problem.
rev13:change the display of pulse counting and fix the ethernet comunication problem when add new baudrate. the ram is ran out and it casue the problem when add the new baudrate.
rev12:add the baudrate 76800
rev11: change the bacnet lib to send out the float type data.
rev10:update the baclib and set the range automatic.
rev9: change the ENC28j60.c and spi.c
rev8: store the data into flash
rev7: add the data formate as minipanel has and detele some unuseful data.
rev6: add the mstp and bacnet ip lib
rev5: fix the data length  error
rev4: fix the buf of isp do not jump to the app code.
rev3: add the analog pulse counting.
rev2: add the tcpip protocol and the Ethernet port modbus is ok.
rev1: add the mstp for the t3 modules.
rev0: finish the function for the t3-6ao and t3-22in to take place of the old t3 modules.