WTS6-E: Strap-On External Temperature Sensor
- May 17, 2016
- 0 Comment(s)
The strap-on temperature sensor is used for sensing the temperature of pipework in heating, ventilation and air conditioning systems.
Pitot Tube
- May 17, 2016
- 0 Comment(s)
The Pitot Tube is a differential pressure producer suitable for air flow measurement.It includes multiple sensing points to measure total and static pressures. It is easy to install and cost effective. It offers simple, low cost installation into pipes and ducts, and high energy savings due to its low unrecovered pressure loss. There are no moving parts or sharp edges to wear, so long term accuracy can be maintained. It contains a lid,connector and two 1 meter length pipes.All Extrusion pipe could be cut on site with a hacksaw,no need a special tool.For example:Buy a 12″ long pipe,and cut to 8″,buy 1m long pipe and cut to the length needed.
Plastic Switch Box
- May 17, 2016
- 0 Comment(s)
The Switch BOX series sealed box is widely used in industries such as machinery and machine tool, electric equipment, power, communication, automation, etc., as well as in marine, metallurgy, chemical, aerospace, rail transportation, sewage treatment, architecture and so on. Depending on the requirements, it can be used as sealed box, instrument case, field control cabinet, or illumination box. It also can be used as terminal box or button box.
Momentary Push Button
- May 17, 2016
- 0 Comment(s)
HPB5 series are suitable to industrial control circuit with AC 50Hz or 60HZ, 0~380V rated voltage and 0~220V D C operating voltage,used for the control of magnetic starter, contactor, relay and other electric circuit.
Outdoor Air Temperature Sensor, Overmolded
- May 17, 2016
- 0 Comment(s)
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
CO2 Sensor
- May 17, 2016
- 0 Comment(s)
The CO2 sensor with Humidity & Temp transmitters are designed for environmental monitoring and controlling in industrial, commercial and other buildings. These transmitters can be used for indoor C02, temperature and humidity monitoring. The modbus interface provides easy setup and integration into large systems.Supports Modbus RTU over both the Ethernet port and the RS485 port,supports Bacnet over both the Ethernet port (IP) and the RS485 port (MSTP).
Split core Current Transformer, 5A output
- May 17, 2016
- 0 Comment(s)
The split core current transformer are used for monitoring power of large electrical loads and electrical services. Current flowing in the primary conductor creates a proportional current in the secondary output coil with a range of 0 to 5 amps. This is typically used to drive current indicators on large electrical panels. It is also compatible with commonly used power meters in the industry such as our Three Phase Power Meter.
are ideal where space is limited, such as when metering multiple loads within a panel board. Use for current measurement, energy metering, load surveys, demand metering, energy research, and submetering applications.
Tstat 2 Series Thermostat
- May 17, 2016
- 0 Comment(s)
TSTAT 2 series on/off thermostat is mainly used in central air-conditioning heating and cooling system. It works with TSC series temperature sensor. It provides temperature control for central air-conditioning fan coil cooling / heating motorized valve or other electric actuator by the control signal which produced by comparison of actual tested ambient temperature and setting temperature.
High temperature probe for Floor Heating & Solar applications
- May 17, 2016
- 0 Comment(s)
This temperature probe is suitable for a variety or high temperature applications such as floor heating, solar heating systems and domestic hot water heaters to name a few. The sensor element is housed in a stainless steel probe which is 6mm diameter x 50mm [2in] long. The cable is 4.5 meter long and is a high temperature material that is tough and highly durable.The probe is available with custom thermistors and Pt elements, nearly all the popular ranges are available with very small minimum order quantity.
General Purpose Relay
- May 17, 2016
- 0 Comment(s)
Featuring top-mounted terminals, this enclosed power relay has a flange-type mounting bracket for mounting in panels and ductwork. These relays are good as status points for high voltage circuits, connect the coil to the high voltage equipment and wire the dry contacts directly into the low voltage side of any of the controllers and thermostats on this site. The spade terminals make for easy troubleshooting in the field and good isolation of high & low voltage circuits.
High power switching capacity for motors and other inductive loads. The standard stocking item is the 20 amp version though we have 30 and 40 amp available as well as other variations shown in the datasheet, by request.